-- *****************************************************************
-- CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB: MIB for limiting resources
--
-- August 2005, Subrahmanya Hegde
--
-- Copyright (c) 2005, 2006, 2008 by cisco Systems Inc.
-- All rights reserved.
-- *****************************************************************CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Unsigned32,Gauge32,Counter32,Counter64,NOTIFICATION-TYPEFROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUP,NOTIFICATION-GROUPFROM SNMPv2-CONF
TruthValue,TEXTUAL-CONVENTION,RowStatus,StorageType,TimeStampFROM SNMPv2-TC
entPhysicalIndex
FROM ENTITY-MIB
ciscoMgmt
FROM CISCO-SMI;ciscoL4L7moduleResourceLimitMIB MODULE-IDENTITY
LAST-UPDATED"200803070000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-l4l7security@cisco.com"DESCRIPTION"The MIB module for managing resource classes
and configuring limits(max/min) to different
resources. The resource referenced in this MIB
are in addition to resource information availale
in other MIBs. This MIB is applicable to
L4-L7 modules which supports managing
resource limits using a centralized approach.
The resources (but not limited to) configured are
of following categories:
- TCP/IP Connections
- MAC Addresses
- syslog buffer, ACL Memmory
- NAT Translations etc
ciscoL4L7ResourceClassTable is used for adding/deleting
resource classes. Resource class is identified
by a name to which limits of multiple resources can
be configured.
ciscoL4L7ResourceLimitTable is used for adding/deleting
limits to resources in a resource class. This limit
is either maximum value and/or minimum value.
ciscoL4L7ResourceRateLimitTable is used for adding/deleting
rate limits to resources in a resource class.
Terminologies used:
ARP - Address Resolution Protocol.
ACL - Access Control List.
NAT - Network Address Translation.
NBAR - Network Based Application Recognition.
BPDU - Bridge Protocol Data Unit."REVISION"200803070000Z"DESCRIPTION"- Added TEXTUAL-CONVENTION CiscoResourceType.
- Added table ciscoL4L7ResourceUsageSummaryTable.
- Added an OBJECT-GROUP
ciscoL4L7ResourceUsageSummaryGroup.
- Deprecated MODULE-COMPLIANCE
ciscoL4L7ResourceLimitComplianceRev1.
- Added MODULE-COMPLIANCE
ciscoL4L7ResourceLimitComplianceRev2."REVISION"200802070000Z"DESCRIPTION"- Added following enumerations in CiscoRateLimitResourceType
sslConnections (9)
mgmtBandwidth (10)
throughput (11)
missedMac (12)
httpCompression (13)
- Updated the description of bandwidth(4) enumeration in
CiscoRateLimitResourceType."REVISION"200606190000Z"DESCRIPTION"- Added following enumerations in CiscoResourceLimitType
hosts (15)
ipsecSessions (16)
asdmSessions (17)
sshSessions (18)
telnetSessions (19)
- Added following objects in ciscoL4L7ResourceLimitTable
crlResourceLimitCurrentUsage
crlResourceLimitPeakUsage
crlResourceLimitReqsDeniedCount
- Added following objects in ciscoL4L7RateLimitTable
crlRateLimitResourceCurrentUsage
crlRateLimitResourcePeakUsage
crlRateLimitResourceReqsDeniedCount
- Added following objects:
clrResourceLimitReachedNotifEnabled
clrResourceRateLimitReachedNotifEnabled
- Added following Notification objects
clrResourceLimitReached
clrResourceRateLimitReached
- Added following in Compliance/Conformance
ciscoL4L7ResourceLimitComplianceRev1."REVISION"200508050000Z"DESCRIPTION"Initial version of the MIB module."
::={ ciscoMgmt 480}ciscoL4L7ResourceLimitNotifs OBJECTIDENTIFIER::={ ciscoL4L7moduleResourceLimitMIB 0}ciscoL4L7ResourceLimitMIBObjects OBJECTIDENTIFIER::={ ciscoL4L7moduleResourceLimitMIB 1}ciscoResourceLimitMIBConform OBJECTIDENTIFIER::={ ciscoL4L7moduleResourceLimitMIB 2}crlResource OBJECTIDENTIFIER::={ ciscoL4L7ResourceLimitMIBObjects 1}crlNotificationObjects OBJECTIDENTIFIER::={ ciscoL4L7ResourceLimitMIBObjects 2}CiscoResourceClass ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This textual convention is used for representing
resource classes. A resource class is identified by
a name preferably in human readable form. This resource
class is used for identifying different type of resources.
The resource class can represent single resource type or
multiple resource type.
Resource category examples:
memory, connections
NAT(network address translation) translations,
number of syslog messages etc."SYNTAXOCTETSTRING(SIZE(0..64))CiscoResourceLimitType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This object represents the resource type.
The possible values are :
all (1) : This is not a resource. However
this value acts as the wild card
value to set all the resources
at the same time. If an entry
exists with this value, then
for all the resources that are
not configured in this table will
have the value specified in this
entry.
macAddresses(2) : The number of MAC addresses allowed in
the MAC address table.
concurrentConns (3) : Concurrent TCP/UDP connections that are
supported. Connections exist between
any two hosts. This is applicable
for through the box connections only.
mgmtConnections (4) : This is applicable for to-the-box
traffic only.
proxyConns (5) : Sticky connections limit traffic to
the individual real servers by allowing
multiple connections from the same client
to stick (or attach) to the same real
server using source IP addresses,
source IP subnets, cookies, and the
secure socket layer (SSL) or
by redirecting these connections using
Hypertext Transfer Protocol (HTTP)
redirect messages.
probes (6) : the number of health probes.
stickyEntries (7) : the number of sticky entries.
This refers to statically configured
entries and dynamically created ones.
It represents the pool of entries
available for use/re-use.
natTranslations (8) : the number of NAT Translations.
regexState (9) : Regular expression state.
Regex states are nodes in the
regular expression state graph,
used for matching and sticking on HTTP
fields such as URL, header, cookies.
aclMemory (10) : Memory that is allocated for managing
ACLs.
ipReassemBuffer (11) : buffer that is allocated for IP
Reassembly.
syslogBuffer (12) : buffer that is allocated for syslog
messages that can be logged in the
system.
tcpOOOBuffer (13) : buffer that is allocated for TCP Out Of
Order packets.
sslConnections (14) : The number of SSL Connections.
hosts (15) : Number of hosts allowed through the system.
ipsecSessions (16) : Number of IPSec management sessions.
asdmSessions (17) : Number of ASDM management sessions.
sshSessions (18) : Number of SSH management sessions.
telnetSessions (19) : Number of Telnet management sessions."SYNTAXINTEGER{all(1),
macAddresses(2),concurrentConns(3),mgmtConnections(4),proxyConns(5),probes(6),stickyEntries(7),natTranslations(8),regexState(9),aclMemory(10),syslogBuffer(11),ipReassemBuffer(12),tcpOOOBuffer(13),sslConnections(14),hosts(15),ipsecSessions(16),asdmSessions(17),
sshSessions(18),telnetSessions(19)}CiscoRateLimitResourceType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This object represents the resource type
for which rate limiting needs to be done.
The value for rate limiting is specified
in crlRateLimitResourceMin and
crlRateLimitResourceMax.
The possible value(s) are :
all (1) : This value represents a wildcard
value to mean all the resources.
arpRequestsXmt (2) : ARP requests generated per second
arpResponses (3) : ARP responses to received ARP requests
per second.
bandwidth (4) : Bandwidth of the card in bytes
per second.
connections (5) : connections per second.
appInspections (6) : application inspections per second.
syslog (7) : syslog messages per second.
sslBandwidth (8) : SSL bandwidth in bytes per second.
sslConnections (9) : SSL connections per second.
mgmtBandwidth (10): Management (to-the-ACE) traffic
in bytes per second.
throughput (11): User (through-the-ACE) traffic
in bytes per second.
missedMac (12): Number of ARP resolution requests
in packets per second.
httpCompression (13): Compression rate for HTTP traffic
in bytes per second."SYNTAXINTEGER{
all(1),arpRequestsXmt(2),arpResponses(3),bandwidth(4),connections(5),appInspections(6),syslog(7),sslBandwidth(8),sslConnections(9),mgmtBandwidth(10),throughput(11),missedMac(12),httpCompression(13)}CiscoResourceType ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"This object represents a resource type.
The possible values for this object are:
lMacAddresses (1) : Refer to 'macAddresses' in
CiscoResourceLimitType.
lConcurrentConns (2) : Refer to 'concurrentConns' in
CiscoResourceLimitType.
lMgmtConnections (3) : Refer to 'mgmtConnections' in
CiscoResourceLimitType.
lProxyConns (4) : Refer to 'proxyConns' in
CiscoResourceLimitType.
lProbes (5) : Refer to 'probes' in
CiscoResourceLimitType.
lStickyEntries (6) : Refer to 'stickyEntries' in
CiscoResourceLimitType.
lNatTranslations (7) : Refer to 'natTranslations' in
CiscoResourceLimitType.
lRegexState (8) : Refer to 'regexState' in
CiscoResourceLimitType.
lAclMemory (9) : Refer to 'aclMemory' in
CiscoResourceLimitType.
lIpReassemBuffer (10) : Refer to 'ipReassemBuffer' in
CiscoResourceLimitType.
lSyslogBuffer (11) : Refer to 'syslogBuffer' in
CiscoResourceLimitType.
lTcpOOOBuffer (12) : Refer to 'tcpOOOBuffer' in
CiscoResourceLimitType.
lSslConnections (13) : Refer to 'sslConnections' in
CiscoResourceLimitType.
lHosts (14) : Refer to 'hosts' in
CiscoResourceLimitType.
lIpsecSessions (15) : Refer to 'ipsecSessions' in
CiscoResourceLimitType.
lAsdmSessions (16) : Refer to 'asdmSessions' in
CiscoResourceLimitType.
lSshSessions (17) : Refer to 'sshSessions' in
CiscoResourceLimitType.
lTelnetSessions (18) : Refer to 'telnetSessions' in
CiscoResourceLimitType.
rlArpRequestsXmt (19) : Refer to 'arpRequestsXmt' in
CiscoRateLimitResourceType.
rlArpResponses (20) : Refer to 'arpResponses' in
CiscoRateLimitResourceType.
rlBandwidth (21) : Refer to 'bandwidth' in
CiscoRateLimitResourceType.
rlConnections (22) : Refer to 'connections' in
CiscoRateLimitResourceType.
rlAppInspections (23) : Refer to 'appInspections' in
CiscoRateLimitResourceType.
rlSyslog (24) : Refer to 'syslog' in
CiscoRateLimitResourceType.
rlSslBandwidth (25) : Refer to 'sslBandwidth' in
CiscoRateLimitResourceType.
rlSslConnections (26) : Refer to 'sslConnections' in
CiscoRateLimitResourceType.
rlMgmtBandwidth (27) : Refer to 'mgmtBandwidth' in
CiscoRateLimitResourceType.
rlThroughput (28) : Refer to 'throughput' in
CiscoRateLimitResourceType.
rlMissedMac (29) : Refer to 'missedMac' in
CiscoRateLimitResourceType.
rlHttpCompression (30) : Refer to 'httpCompression' in
CiscoRateLimitResourceType."SYNTAXINTEGER{lMacAddresses(1),lConcurrentConns(2),lMgmtConnections(3),lProxyConns(4),
lProbes(5),lStickyEntries(6),lNatTranslations(7),lRegexState(8),lAclMemory(9),lIpReassemBuffer(10),lSyslogBuffer(11),lTcpOOOBuffer(12),lSslConnections(13),lHosts(14),lIpsecSessions(15),lAsdmSessions(16),lSshSessions(17),lTelnetSessions(18),rlArpRequestsXmt(19),rlArpResponses(20),
rlBandwidth(21),rlConnections(22),rlAppInspections(23),rlSyslog(24),rlSslBandwidth(25),rlSslConnections(26),rlMgmtBandwidth(27),rlThroughput(28),rlMissedMac(29),rlHttpCompression(30)}ciscoL4L7ResourceClassTable OBJECT-TYPESYNTAXSEQUENCEOF CiscoL4L7ResourceClassEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table contains one row per resource class.
This table is used for adding/deleting the resource
class in the system. A resource class can contain
limits for different category of resources and
these resources can be configured using other tables."
::={ crlResource 1}ciscoL4L7ResourceClassEntry OBJECT-TYPESYNTAX CiscoL4L7ResourceClassEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about a particular resource class.
Each entry provides the name of class.
The entPhysicalIndex refers to resource manageable
component in entPhysicalTable with
entPhysicalClass -> 'module'."INDEX{
entPhysicalIndex,
crlResourceClassName
}::={ ciscoL4L7ResourceClassTable 1}
CiscoL4L7ResourceClassEntry ::=SEQUENCE{
crlResourceClassName CiscoResourceClass,
crlResourceClassStorageType StorageType,
crlResourceClassRowStatus RowStatus}crlResourceClassName OBJECT-TYPESYNTAX CiscoResourceClass
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object identifies a unique resource class
in a resource manageable component identified
by entPhysicalIndex."::={ ciscoL4L7ResourceClassEntry 1}
crlResourceClassStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.
This object can not be modified when the value of
crlResourceClassRowStatus is 'active'."DEFVAL{ nonVolatile }::={ ciscoL4L7ResourceClassEntry 2}crlResourceClassRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used for adding/deleting
resource classes in a system."::={ ciscoL4L7ResourceClassEntry 3}ciscoL4L7ResourceLimitTable OBJECT-TYPESYNTAXSEQUENCEOF CiscoL4L7ResourceLimitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table is used for adding resource limits
to resources in a resource class."::={ crlResource 2}ciscoL4L7ResourceLimitEntry OBJECT-TYPESYNTAX CiscoL4L7ResourceLimitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about a particular resource in a resource
class. Each entry provides the type of resource,
the limit that is supported for that resource
and type of the limit value."INDEX{
crlResourceClassName,
crlResourceLimitType
}::={ ciscoL4L7ResourceLimitTable 1}
CiscoL4L7ResourceLimitEntry ::=SEQUENCE{
crlResourceLimitType CiscoResourceLimitType,
crlResourceLimitValueType INTEGER,
crlResourceLimitMin Unsigned32,
crlResourceLimitMax Unsigned32,
crlResourceLimitStorageType StorageType,
crlResourceLimitRowStatus RowStatus,
crlResourceLimitCurrentUsage Gauge32,
crlResourceLimitPeakUsage Gauge32,
crlResourceLimitReqsDeniedCount Counter32
}crlResourceLimitType OBJECT-TYPESYNTAX CiscoResourceLimitType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object represents the type of
resource in a resource class identified
by crlResourceClassName."::={ ciscoL4L7ResourceLimitEntry 2}crlResourceLimitValueType OBJECT-TYPESYNTAXINTEGER{absolute(1),percentage(2)}MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object represents the type of value specified
in crlResourceLimitMax and crlResourceLimitMin objects.
The possible values are :
absolute (1) : the value represents an absolute number.
percentage (2) : the value represents the % of the total
available for the system. In this case
only crlResourceLimitMax object is
applicable."DEFVAL{ percentage }::={ ciscoL4L7ResourceLimitEntry 3}
crlResourceLimitMin OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object represents the rate limit allowed for
the resource identified by 'ciscoResourceLimitType'.
This value cannot be greater than the value
specified in ciscoResourceLimitMax.
The value zero signifies that this object is
not applicable to the resource."DEFVAL{0}::={ ciscoL4L7ResourceLimitEntry 4}crlResourceLimitMax OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object represents the limit allowed for
the resource identified by 'ciscoResourceLimitType'.
The value zero specifies that this resource
can be used until the system limit reached."DEFVAL{0}::={ ciscoL4L7ResourceLimitEntry 5}crlResourceLimitStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrent
DESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.
This object cannot be modified when the value of
crlResourceLimitRowStatus is 'active'."DEFVAL{ nonVolatile }::={ ciscoL4L7ResourceLimitEntry 6}crlResourceLimitRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used for adding/deleting
entries in this table."::={ ciscoL4L7ResourceLimitEntry 7}crlResourceLimitCurrentUsage OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the number of resources identified by
'ciscoResourceLimitType', that are currently being used in
the system."::={ ciscoL4L7ResourceLimitEntry 8}crlResourceLimitPeakUsage OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object represents the peak usage of the resource
identified by 'ciscoResourceLimitType' since the statistics
were last cleared either through the command line interface or
bacause of the system reboot."::={ ciscoL4L7ResourceLimitEntry 9}crlResourceLimitReqsDeniedCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the number of resource requests that
were denied when the configured resource limit is exceeded
for the resource identified by 'ciscoResourceLimitType'.
The value for resource limiting is specified
in 'crlResourceLimitMax'."::={ ciscoL4L7ResourceLimitEntry 10}ciscoL4L7ResourceRateLimitTable OBJECT-TYPESYNTAXSEQUENCEOF CiscoL4L7ResourceRateLimitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table is used for adding/deleting
the rate limiting of the resources in a
resource class."::={ crlResource 4}
ciscoL4L7ResourceRateLimitEntry OBJECT-TYPESYNTAX CiscoL4L7ResourceRateLimitEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Information about an entry in the table
Each entry provides the name of group, the rate
configured for a resource."INDEX{
crlResourceClassName,
crlRateLimitResourceType
}::={ ciscoL4L7ResourceRateLimitTable 1}
CiscoL4L7ResourceRateLimitEntry ::=SEQUENCE{
crlRateLimitResourceType CiscoRateLimitResourceType,
crlRateLimitResourceMin Unsigned32,
crlRateLimitResourceMax Unsigned32,
crlRateLimitResourceStorageType StorageType,
crlRateLimitResourceRowStatus RowStatus,
crlRateLimitResourceCurrentUsage Gauge32,
crlRateLimitResourcePeakUsage Gauge32,
crlRateLimitResourceReqsDeniedCount Counter32}crlRateLimitResourceType OBJECT-TYPESYNTAX CiscoRateLimitResourceType
MAX-ACCESSnot-accessibleSTATUScurrent
DESCRIPTION"This object represents the resource type
for which rate limiting needs to be done.
The value for rate limiting is specified
in crlRateLimitResourceMin and
crlRateLimitResourceMax."::={ ciscoL4L7ResourceRateLimitEntry 1}crlRateLimitResourceMin OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object represents the rate limit allowed for
the resource identified by 'crlRateLimitResourceType'.
This value cannot be greater than the value
specified in crlRateLimitResourceMax.
The value zero signifies that this object is
not applicable to the resource."DEFVAL{0}::={ ciscoL4L7ResourceRateLimitEntry 2}crlRateLimitResourceMax OBJECT-TYPESYNTAXUnsigned32MAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object represents the limit allowed for
the resource identified by 'crlRateLimitResourceType'.
The value zero specifies that this resource
can be used until the system limit reached."DEFVAL{0}::={ ciscoL4L7ResourceRateLimitEntry 3}crlRateLimitResourceStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.
This object cannot be modified when the value of
crlRateLimitResourceRowStatus is 'active'."DEFVAL{ nonVolatile }::={ ciscoL4L7ResourceRateLimitEntry 4}crlRateLimitResourceRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used for adding/deleting
entries in this table. This object cannot
be set to 'active' until all the mandatory
objects have valid value."::={ ciscoL4L7ResourceRateLimitEntry 5}crlRateLimitResourceCurrentUsage OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-only
STATUScurrentDESCRIPTION"This object indicates the number of resources identified by
'crlRateLimitResourceType', that are currently being used in
the system."::={ ciscoL4L7ResourceRateLimitEntry 6}crlRateLimitResourcePeakUsage OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the peak usage of the resource
identified by 'crlRateLimitResourceType' since the statistics
were last cleared either through the command line interface or
bacause of the system reboot."::={ ciscoL4L7ResourceRateLimitEntry 7}crlRateLimitResourceReqsDeniedCount OBJECT-TYPESYNTAXCounter32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the number of resource requests that
were denied when the configured rate limit is exceeded
for the resource identified by 'crlRateLimitResourceType'.
The value for rate limiting is specified in
'crlRateLimitResourceMax'."::={ ciscoL4L7ResourceRateLimitEntry 8}ciscoL4L7ResourceUsageSummaryTable OBJECT-TYPE
SYNTAXSEQUENCEOF CiscoL4L7ResourceUsageSummaryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table provides the statistics for each resource type
in a system.
The resource usage statistics can be:
- current usage for the resource.
- peak usage for the resource.
- Number of times the resource request were denied when the
configured limit or rate-limit is exceeded for the resource."::={ crlResource 5}ciscoL4L7ResourceUsageSummaryEntry OBJECT-TYPESYNTAX CiscoL4L7ResourceUsageSummaryEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"An entry in ciscoL4L7ResourceUsageSummaryTable. Each entry
provides the resource usage parameters in a system.
An entry is created when an entry is created in
either 'ciscoL4L7ResourceLimitTable' or
'ciscoL4L7ResourceRateLimitTable'.
An entry is deleted when an entry is deleted
from either 'ciscoL4L7ResourceLimitTable' or
'ciscoL4L7ResourceRateLimitTable'."INDEX{ crlResourceSummaryType }::={ ciscoL4L7ResourceUsageSummaryTable 1}
CiscoL4L7ResourceUsageSummaryEntry ::=SEQUENCE{
crlResourceSummaryType CiscoResourceType,
crlResourceSummaryCurrentUsage Gauge32,
crlResourceSummaryPeakUsage Gauge32,
crlResourceSummaryReqsDeniedCount Counter64,
crlResourceSummaryLastClearedTime TimeStamp,
crlResourceSummaryStorageType StorageType,
crlResourceSummaryRowStatus RowStatus}crlResourceSummaryType OBJECT-TYPESYNTAX CiscoResourceType
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This object represents a type of resource in the system."::={ ciscoL4L7ResourceUsageSummaryEntry 1}crlResourceSummaryCurrentUsage OBJECT-TYPESYNTAXGauge32MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the current usage of the resource
in the system."::={ ciscoL4L7ResourceUsageSummaryEntry 2}crlResourceSummaryPeakUsage OBJECT-TYPESYNTAXGauge32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the peak usage of the resource
in the system."::={ ciscoL4L7ResourceUsageSummaryEntry 3}crlResourceSummaryReqsDeniedCount OBJECT-TYPESYNTAXCounter64MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the number of resource requests
that were denied in the system when the configured
limit is exceeded for the resource.
The value for limiting is specified in 'crlResourceLimitMax'
and the value for rate limiting is specified in
'crlRateLimitResourceMax'."::={ ciscoL4L7ResourceUsageSummaryEntry 4}crlResourceSummaryLastClearedTime OBJECT-TYPESYNTAXTimeStampMAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object represents the time when the value of the
object identified by 'crlResourceSummaryPeakUsage' is
last cleared or reset. A value of 0 (zero) signifies
that the value has not been cleared since the last
system reboot."::={ ciscoL4L7ResourceUsageSummaryEntry 5}
crlResourceSummaryStorageType OBJECT-TYPESYNTAXStorageTypeMAX-ACCESSread-createSTATUScurrentDESCRIPTION"The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row.
This object cannot be modified when the value of
'crlResourceSummaryRowStatus' is 'active'."DEFVAL{ nonVolatile }::={ ciscoL4L7ResourceUsageSummaryEntry 6}crlResourceSummaryRowStatus OBJECT-TYPESYNTAXRowStatusMAX-ACCESSread-createSTATUScurrentDESCRIPTION"This object is used for adding/deleting
entries in this table. This object cannot
be set to 'active' until all the mandatory
objects have valid value."::={ ciscoL4L7ResourceUsageSummaryEntry 7}-- notification control objectsclrResourceLimitReachedNotifEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION
"This object controls the generation of
'clrResourceLimitReached' notification.
'true' Indicates that clrResourceLimitReached
notification is to be generated when the
configured resource limit is reached.
The value for resource limiting is specified
in 'crlResourceLimitMax'.
'false' Indicates that clrResourceLimitReached
notification generation is disabled."DEFVAL{ false }::={ crlNotificationObjects 1}clrResourceRateLimitReachedNotifEnabled OBJECT-TYPESYNTAXTruthValueMAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object controls the generation of
'clrResourceRateLimitReached' notification.
'true' Indicates that clrResourceRateLimitReached
notification is to be generated when the
configured resource rate limit is reached.
The value for rate limiting is specified in
'crlRateLimitResourceMax'.
'false' Indicates that clrResourceRateLimitReached
notification generation is disabled."DEFVAL{ false }::={ crlNotificationObjects 2}-- notificationsclrResourceLimitReached NOTIFICATION-TYPEOBJECTS{
crlResourceLimitValueType,
crlResourceLimitMax
}STATUScurrentDESCRIPTION"This notification is generated when the configured resource
limit value specified in 'crlResourceLimitMax' is reached
for a particular resource. This resource is identified by
'crlResourceLimitType' in ciscoL4L7ResourceLimitTable."::={ ciscoL4L7ResourceLimitNotifs 1}clrResourceRateLimitReached NOTIFICATION-TYPEOBJECTS{ crlRateLimitResourceMax }STATUScurrentDESCRIPTION"This notification is generated when the configured rate
limit value specified in 'crlRateLimitResourceMax' is reached
for a particular resource. This resource is identified by
'crlRateLimitResourceType' in ciscoL4L7ResourceRateLimitTable."::={ ciscoL4L7ResourceLimitNotifs 2}-- conformance informationciscoL4L7ResourceLimitConformance OBJECTIDENTIFIER::={ ciscoL4L7moduleResourceLimitMIB 3}ciscoL4L7ResourceLimitCompliances OBJECTIDENTIFIER::={ ciscoL4L7ResourceLimitConformance 1}ciscoL4L7ResourceLimitGroups OBJECTIDENTIFIER
::={ ciscoL4L7ResourceLimitConformance 2}-- compliance statementsciscoL4L7ResourceLimitCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for SNMP entities which implement
CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB."MODULE-- this moduleMANDATORY-GROUPS{
ciscoL4L7ResourceClassGroup,
ciscoL4L7ResourceLimitGroup
}GROUP ciscoL4L7ResourceRateLimitGroup
DESCRIPTION"This group is mandatory for those systems where
rate limiting is supported."::={ ciscoL4L7ResourceLimitCompliances 1}ciscoL4L7ResourceLimitComplianceRev1 MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for SNMP entities which implement
CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB."MODULE-- this moduleMANDATORY-GROUPS{
ciscoL4L7ResourceClassGroup,
ciscoL4L7ResourceLimitGroup,
ciscoL4L7ResourceLimitUsageGroup
}GROUP ciscoL4L7ResourceRateLimitGroup
DESCRIPTION"This group is mandatory for those systems where
rate limiting is supported."GROUP ciscoL4L7ResourceRateLimitUsageGroup
DESCRIPTION"This group is mandatory for those systems where
rate limiting is supported."GROUP ciscoL4L7ResourceNotifEnabledGroup
DESCRIPTION"This group is mandatory for those systems which
implement resource limit notifications."GROUP ciscoL4L7ResourceNotifGroup
DESCRIPTION"This group is mandatory for those systems which
implement resource limit notifications."::={ ciscoL4L7ResourceLimitCompliances 2}ciscoL4L7ResourceLimitComplianceRev2 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for SNMP entities which implement
CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB."MODULE-- this moduleMANDATORY-GROUPS{
ciscoL4L7ResourceClassGroup,
ciscoL4L7ResourceLimitGroup,
ciscoL4L7ResourceLimitUsageGroup
}GROUP ciscoL4L7ResourceRateLimitGroup
DESCRIPTION"This group is mandatory for those systems where
rate limiting is supported."GROUP ciscoL4L7ResourceRateLimitUsageGroup
DESCRIPTION"This group is mandatory for those systems where
rate limiting is supported."GROUP ciscoL4L7ResourceNotifEnabledGroup
DESCRIPTION"This group is mandatory for those systems which
implement resource limit notifications."GROUP ciscoL4L7ResourceNotifGroup
DESCRIPTION"This group is mandatory for those systems which
implement resource limit notifications."GROUP ciscoL4L7ResourceUsageSummaryGroup
DESCRIPTION"This group is mandatory for those systems which
implement resource limiting and/or rate limiting
of resource."::={ ciscoL4L7ResourceLimitCompliances 3}-- MIB groupingsciscoL4L7ResourceClassGroup OBJECT-GROUPOBJECTS{
crlResourceClassStorageType,
crlResourceClassRowStatus
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
resource class in a system."::={ ciscoL4L7ResourceLimitGroups 1}ciscoL4L7ResourceLimitGroup OBJECT-GROUP
OBJECTS{
crlResourceLimitValueType,
crlResourceLimitMin,
crlResourceLimitMax,
crlResourceLimitStorageType,
crlResourceLimitRowStatus
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
limits of resources in a resource class."::={ ciscoL4L7ResourceLimitGroups 2}ciscoL4L7ResourceRateLimitGroup OBJECT-GROUPOBJECTS{
crlRateLimitResourceMin,
crlRateLimitResourceMax,
crlRateLimitResourceStorageType,
crlRateLimitResourceRowStatus
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
rate limits for resources."::={ ciscoL4L7ResourceLimitGroups 3}ciscoL4L7ResourceLimitUsageGroup OBJECT-GROUPOBJECTS{
crlResourceLimitCurrentUsage,
crlResourceLimitPeakUsage,
crlResourceLimitReqsDeniedCount
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
limit usage for resources."::={ ciscoL4L7ResourceLimitGroups 4}ciscoL4L7ResourceRateLimitUsageGroup OBJECT-GROUPOBJECTS{
crlRateLimitResourceCurrentUsage,
crlRateLimitResourcePeakUsage,
crlRateLimitResourceReqsDeniedCount
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
rate limit usage for resources."::={ ciscoL4L7ResourceLimitGroups 5}ciscoL4L7ResourceNotifEnabledGroup OBJECT-GROUPOBJECTS{
clrResourceLimitReachedNotifEnabled,
clrResourceRateLimitReachedNotifEnabled
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
limit usage for resources."::={ ciscoL4L7ResourceLimitGroups 6}ciscoL4L7ResourceNotifGroup NOTIFICATION-GROUP
NOTIFICATIONS{
clrResourceLimitReached,
clrResourceRateLimitReached
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
rate limit usage for resources."::={ ciscoL4L7ResourceLimitGroups 7}ciscoL4L7ResourceUsageSummaryGroup OBJECT-GROUPOBJECTS{
crlResourceSummaryCurrentUsage,
crlResourceSummaryPeakUsage,
crlResourceSummaryReqsDeniedCount,
crlResourceSummaryLastClearedTime,
crlResourceSummaryStorageType,
crlResourceSummaryRowStatus
}STATUScurrentDESCRIPTION"The collection of objects which are used to represent
usage summary for resources across the system."::={ ciscoL4L7ResourceLimitGroups 8}END